This kit is designed to help electricians and HVAC technicians solve problems quicker. Test first for overheated electrical devices using an IR thermometer; then use the clamp meter and voltage detector to find out more about the problem
Fluke 62 MAX+. Small in size. Big on toughness.
Dust and water-resistant: IP54 rated.
Rugged: 3-meter (9.8-foot) drop tested.
Ergonomically designed: Completely redesigned for a more natural hand fit.
Distance to spot: 12:1.
Dual lasers: Identifies area to be measured.
Large, backlit display: Makes data easier to read, even in dark areas.
True RMS AC voltage and current for accurate measurements on non-linear signals.
Resistance measurement up to 40 kΩ with continuity detection.
Slim, ergonomic design.
CAT IV 300V/CAT III 600 V safety rating.
Fluke 1AC II VoltAlert™ Voltage Detector
Voltbeat™ technology and continuous self-test, so always know it’s working.
Upon detection, tip glows and beeper sounds.
Voltage detection of 90 to 1000 VAC.
CAT IV 1000 V for added protection.
Fluke C115 Soft Case
Lightweight soft case to provide optimal protection and accessory storage.
Fluke 62 MAX+ Infrared Thermometer
-30°C to 650°C (-22°F to 1202°F)
±1.0°C or ±1.0% of reading, whichever is greater
-10°C to 0°C: ±2.0
-30°C to -10°C: ±3.0
Response time (95%)
< 300 ms (95% of reading)
8 to 14 microns
0.10 to 1.00
12:1 (calculated at 90% energy)
Repeatability of readings
±0.5% of reading or < ±0.5°C (1°F), whichever is greater
8 hours with laser and backlight on
255 g (8.99 oz)
175 x 85 x 75 mm (6.88 x 3.34 x 2.95 in)
0°C to 50°C (32°F to 122°F)
-20°C to 60°C (-4°F to 140°F), (without battery)
10% to 90% RH non-condensing at 30°C (86°F)
2000 meters above mean sea level
12,000 meters above mean sea level
IP 54 per IEC 60529
Vibration and shock
IEC 68-2-6 2.5 g, 10 to 200 Hz, IEC 68-2-27, 50 g, 11 ms
EN 61326-1:2006 EN 61326-2:2006
Standards and agency approval
EN/IEC 61010-1: 2001
FDA and EN 60825-1 Class II
Fluke 323 True RMS Clamp Meter
2% ±5 digits
(45 Hz to 65 Hz)
2.5% ±5 digits
(65 Hz to 400 Hz)
1.5% ±5 digits
1.0% ±5 digits
400.0 Ω/ 4000 Ω
1.0% ±5 digits
≤ 70 Ω
H x W x D (mm)
207 x 75 x 34
Max wire diameter
30 mm (600 MCM)
CAT III 600 V
CAT IV 300 V
Fluke 1AC-II VoltAlert
Senses the steady state electrostatic ﬁeld produced by ac voltage through insulation without requiring contact to the bare conductor. A red glow at the tip and a beeping noise (if not switched OFF) indicates the presence of voltage.
Voltage sensing ranges
Nominally, 90 VAC to 1000 VAC or 200 VAC to 1000 VAC depending on model, 45 Hz to 405 Hz; also a 20 V to 90 V control circuit model
Detector tip style
Blade or round, depending on model
One high intensity red LED
c CSA us, CE, C-Tick
1000 V, CAT IV
-10°C to 50°C
Operating humidity ranges
0% to 95%
(0°C to 30°C)
0% to 75%
(30°C to 40°C)
0% to 45%
(40°C to 55°C)
2 AAA alkaline batteries included
Product does not respond to random electrostatic discharge.